• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Olori Joshua

    Harness Code

    Yes, I see newer machines not with harness code but ECM location code.
  2. Olori Joshua

    Harness Code

    That is very correct. Thank you for the information.
  3. Olori Joshua

    Harness Code

    Thanks for your answer. Yesterday I was curious about it and I removed a harness code connector from a D6R III and I had the below active code on the transmission ECM, with the Code certain functions could not work. I put it back and the code stays ON until I turn OFF the disconnect switch and...
  4. Olori Joshua

    Harness Code

    What exactly is harness code on Caterpillar machines?
  5. Olori Joshua

    CAT 988H Lift and and Tilt linkage position sensors not calibrating

    I am on the machine right now carrying out the tilt linkage position sensor calibration. 1. Was only able to pass the step one which is set the parking brake. 2. Got the attached error as I was racking back the bucket slowly as required by step two. The bucket has not rackback fully when I got...
  6. Olori Joshua

    CAT 988H Lift and and Tilt linkage position sensors not calibrating

    No messing with the sensor LOL. It is my first time carrying out this calibration that is why the many questions for clarification. I do not know how to do what am not sure of. Thank you. I will do just that today and hopefully I got it calibrated successfully. There was no oil leakage. We...
  7. Olori Joshua

    CAT 988H Lift and and Tilt linkage position sensors not calibrating

    Many thanks for your answers. The points are very clear to me now expecially the snubbing effect ( to lessen the end of stroke effect) Please another clarification needed. In setting the sensor linkage to minimum and maximum positions for calibration, do I need not to first connect the sensor...
  8. Olori Joshua

    CAT 988H Lift and and Tilt linkage position sensors not calibrating

    I am here in 2025 commenting on a 2021 post. This forum will even be more helpful in the future. Thanks our senior member Mr. Nige. I have observed that you are always ready to give an answer. Please I have some questions concerning Caterpillar wheel loaders that have electrohydraulic system...
  9. Olori Joshua

    My big 14M steering system problem

    Yea thank you
  10. Olori Joshua

    Vogele Super 1800-1 augers and conveyors working intermittently

    we were able to resolve this problem. The cause of the problem was the engine charging alternator.
  11. Olori Joshua

    My big 14M steering system problem

    Thank you.
  12. Olori Joshua

    Vogele Super 1800-1 augers and conveyors working intermittently

    there's no problem on the electrical circuit wiring. All auger and conveyors solenoids resistance are ok. 24.3 to 24.5 Ohms as I measured. wires ok. No short or open circuit. Terminating resistors CAN 1 and 2 ok. 60.1 Ohms measured at B2 module on CAN 1 and 2 respectively. Do they need any...
  13. Olori Joshua

    Vogele Super 1800-1 augers and conveyors working intermittently

    Thank you for the reply. Yes there is forward movement of the conveyors but intermittently. Yes the problem is on both sides; the auger left and right forward and backward and the conveyors left and right forward and backward. I think it's electrical problem because the voltage to the...
  14. Olori Joshua

    Vogele Super 1800-1 augers and conveyors working intermittently

    When I push the conveyors or the augers push button switches down from the operator desk on manual mode, the augers or the conveyors work but intermittently. Their movement don't continues, they're moving and stopping like something is ceasing. Please any idea on fixing this?
  15. Olori Joshua

    My big 14M steering system problem

    Thank you
  16. Olori Joshua

    Bomag soil stabilizer s/n 101590041070

    It is almost three years now. I am sorry for giving this feedback this late. The problem of the no starting after new injector pumps that were broken were changed was "timing" The mechanic that overhauled the engine had to drop it down again from the machine and confirmed the timing. They...
  17. Olori Joshua

    Bobcat S175 traction solenoid electrical circuit

    Thanks for your reply. The pull wire on this S175 comes from pin 87 of the traction pull relay. The relay is not getting current to its pin 86 to energise so that it can send pull current to the solenoid. The thing is I don't know what condition it should energies and I don't also know where...
  18. Olori Joshua

    Bobcat S175 traction solenoid electrical circuit

    I am having a traction problem with a client S175 Bobcat. All fuses are having current, but no pulling and holding current to the traction solenoid. It can not move forward or reverse. I do not have the electrical schematic drawing to trace where the wires are coming from. Please help...
  19. Olori Joshua

    I need help with S175 Bobcat skidsteer electrical schematic. I have a traction problem.

    Sorry, I meant to say the traction pull relay is not getting current to its pin 86
  20. Olori Joshua

    I need help with S175 Bobcat skidsteer electrical schematic. I have a traction problem.

    My client Bobcat S175 traction solenoid won't pull and hold even after pressing the "press to operate button" on the left hand panel and the cross bar is down. Usually when the "press to operate switch" is pressed when the cross bar is down, you will hear a sound that the traction solenoid has...
Top