• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

genie boom

  1. G

    Help with genie s60x torque hub

    Can I get some guidance on rebuilding a torque hub? Oil is leaking down the inside of the rim. Looks like a hub seal blew out but I can’t find anything with an exploded view of the hub. Any help is appreciated.
  2. T

    JLG 660SJC Boom Lift 2 Speed Issues

    I have a 2001 660SJC track boom lift that is having two speed issues. It is the machine that has a steel tracked excavator undercarriage instead of wheels. Runs great in lower speed but doesnt want to go into 2 speed. It will sometimes surge like it goes into 2 speed for a second and then kicks...
  3. B

    Genie S40/45 wheel lifting off ground

    I work for a equipment rental company here in Phoenix, AZ and we have four Genie S40/45 booms lift that the wheel lifts off the ground when turntable is rotated either clockwise or counterclockwise from stowed position. To give more of a detailed description, machine will be on level ground...
  4. C

    splitting a genie boom

    hey everyone running into some issues and wanted to quiz the collective. have a couple genie 34/22 booms at work that need to split and replace the main rotate bearing assembly (excessive play) tentative plan is to unbolt, jack up the house and support it with steel saw horses (2x2 square tube...
  5. L

    Slack in turntable rotation gear Genie Z45/22

    Hi everyone. I'm looking to buy a 1997 Genie Z45/22 lift. Everything seems to be okay for the age of the lift, but it has a lot of slack in the rotation gear (worm gear system). I've tried to study the service manual to see if there is any way to adjust the tolerance in the worm gear system, but...
  6. J

    Genie S-60 Boom Drives slow and sometimes not at all.

    I have a 1995 Genie S-60 Boom, serial number 785. Took a chance and bought it for $1000. I got it to run, boom functions work from the ground and basket. When I attempt to drive it, it starts to move then seems to "Jump out" of it's hydraulic circuit for lack of better words. There's a change...
  7. A

    Genie Z-45/25J Electrical Problem

    This Genie is having a problem where if you leave it turned on for an extended amount of time (30 minutes or so) it’ll turn off when you press the operate pedal, then if you turn it on, it’ll quickly turn off again until you wait 5 minutes and remove and insert a yellow fuse. any ideas on what...
  8. B

    Genie TZ34/20 Motor Controller

    I have a Genie TZ34/20 that is having an issue with the motor controller. I got a new one in the mail and installed it. It ran for about 20 seconds then it stopped and hasn't worked since. I'm at a dead end on this. Hopefully someone here can help.
  9. K

    Genie 125

    Looking for some help with a Genie 125 boom I’m working on. Getting fault code LSB8SA (50degree angle limit switch) the boom will not extend past 75 feet no matter what angle it’s on. I know it’s not an issue with axle extend because the boom goes up fine, just won’t extend fully. Tried...
  10. M

    Genie Z45 drive inoperable

    Good day all! Newbie to the forum I’ve got a Genie z45/25 S/N z452506-28022. This this is making me pull my hair out a bit. All functions work but drive won’t work, I’ve calibrated joystick, also tried another joystick and still no luck. I’ve noticed some corrosion on the pins at the ALC500...
Top