• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Browfurrow83

  1. B

    650J halts going over bumps

    Did pop the cover off of the TCU clean dry and unburnt in there cleaned ground-strap to fender CAN Measures 120 ohm with the TCU end terminating resistor unplugged likewise at the engine end. 60 ohm back-probing with both in. I was checking the wrong one.
  2. B

    650J halts going over bumps

    Had to leave today. I plan when I get back to continue to trace P12 wire back from the 10 amp fuse--because bypassing P12 did not seem to work--12V power did seem to work. The laps around the field without failure could have been a fluke so confirm that power works I guess.
  3. B

    650J halts going over bumps

  4. B

    650J halts going over bumps

    Go a chance to go back for a while today. TCU had codes of F3P5 FP93 F393 F3X1 F359 AI'd these nothing really jumped out from the results Ran a Jumper from the large wires in the fuse panel to a back-probe at the red wire in the leftmost plug of TCU did 2 laps around field without detecting...
  5. B

    650J halts going over bumps

    Serial 109143 Speeds in the mid 2s the crawler briefly comes to a stop--throwing the operator forward or back--happens more often in reverse when going faster--and resumes with no code. New TCU relay<it would not move at all with a CAN failure code this error was here before that but it has...
  6. B

    MQ Whisperwatt 15 shutdown

    Yep Probing around for voltages that are abnormal, I find a lot around 5 at the voltage reg plug but I have nothing to compare this to. the ECU appears to be getting good voltage, the only one that looks fishy turned out to be the white wire from the alternator when I followed it but it comes up...
  7. B

    MQ Whisperwatt 15 shutdown

    12.8V Held the shutoff back and cranked it dropped to 11V. It is a new alternator and when the engine is running it charges at 13.9 could point to the controller seeing low voltage through its wiring
  8. B

    MQ Whisperwatt 15 shutdown

    Glow plug flashes 2 long 6 short twice and the engine shuts down with the switch in either start or run In run it is 60Hz even when cold After a several starting attempts this goes away and the machine runs normal right on 60 hz Machine cools over night and it is the same thing the next morning...
  9. B

    GTH 644 No drive unless a function is called for

    Has anybody run into this one? I am wondering if it has to do with the clutch cutoff.
  10. B

    310 SK Slow Functions Loader and Hoe

    1T0310SKPEE273990
  11. B

    310 SK Slow Functions Loader and Hoe

    Thank's for this the machine is in another guys shop in another town, but I will suggest we get a hyd filter and autopsy the old one. I did notice external leakage on the pump but it was not a today kind of problem. Adept ape is a great channel!
  12. B

    Genie S 85 ,2002

    Have you checked the EDC wire plugs?
  13. B

    Skyjack SJIII3219 Problem

    Try hitting contactor with small hammer. Sometimes they weld and wont turn the power off--it happens more often with low battery, high current, low voltage. It is just an idea, I don't understand your post. if this works you should still change the contactor--make sure you get 24 volt at the...
  14. B

    310 SK Slow Functions Loader and Hoe

    I have not had a chance to look at the machine in any depth--have just done some routine service so far--does this jump out at anybody as anything obvious? Hours are about 10 000.
  15. B

    Ingersoll Rand XP 185 overheat no apparent cause

    engine
See more
Top