• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. F

    Genie z32/24 boom lift rotator seal

    I am trying to put new seals in the basket rotator. I can not get the pressure seal in. I warmed it in hot water to slip it on and then used a hose clap from turbo hose to squeeze it down. It is still to big to get in housing. The side that goes in 1st is flared which makes it harder.
  2. F

    bobcat 863 blowing seals in carrier

    still working on my 863. the hydrostatic motor carrier blows out the seals twice within minutes of moving it. took to dealer and it happened to them twice also. last time up on blocks it ran ok for 15min. , then when on ground blew out within 5 min. brought it home. took hydrostatic motor apart...
  3. F

    genie boomlift decreased groundspeed

    genie z34/22dc, electric motors. ground speed had been good, sat for a month and now very slow ground speed both forward and reverse, will not go faster. checked all batteries and they are good. have 51 volts to pr2 solenoid. not sure how to check ? on forward/reverse control in basket or...
  4. F

    Bobcat 863 fault code 33-23

    I put new controller in and everything worked fine but before I could put bucket back on lift and tilt would not work. Have code 33-23. I can not find any bad wiring. Remove each harness from controller and reconnected them. Battery is new and holds charge. I disconnected battery before working...
  5. F

    bobcat 863 code 33-23 and 13-07

    still working on this salvage project. the lift arms and tilt do not work. no warning lights on and all for lites are on for lift arms to work. the other problem that may be related is brake solenoid shaft, etc falls down in chain case. when i test the solenoid with battery , it pulls in with...
  6. F

    bobcat 863 disc brake assembly bolt breaking

    help. what am i screwing up for 2nd time. my disc brake assembly bolt breaks and everything falls into chain case. tested solenoid and it works pulling shaft in. is solenoid the only thing that holds wedge up?
  7. F

    drive wheel traction

    34/22dc genie boom lift. can i put snow chains on drive tires or put different tires with big tread for better traction. would this hurt the electric motors? does only 1 tire spin when on mud or should both? i was hoping to use machine around job sites but maybe it is only built for concrete...
  8. F

    hydraulic pressure testing

    genie z34/22 platform lift and rotator problems. can you put pressure gauge directly to cylinder manifold or do you have to put a Tee into line and have all lines hooked up to get the correct hydraulic pressure? is it ok to use automatic transmission fluid in place of hydraulic fluid in a genie?
  9. F

    still have problem with z34/22 rotator

    i had posted before this problem and still can't figure it out and now a new problem with jib boom cylinder. rotator will not move. took platform off, cleaned counter balance valves - did not find any dirt, ect. bleed oil and will not move while bleeding or after. jib boom cylinder lifts good...
  10. F

    bobcat 863 seat bar problem

    i keep can't figure out seat bar fault - sensor to grd. i have read other posts . i have replaced plastic bushing and sensor for seat bar but still get fault 11-06. i have cleaned all the harness wire connections i can find. only wires i found bare were on hydraulic oil sensor and replaced that...
  11. F

    platform won't swing 34/22 genie

    genie 34/22dc boom lift platform won't swing. have fluid to rotator. when i bleed either of the 2 bleeders platform will swing but other wise it won't move. i took rotator manifold apart and don't see any dirt, etc. in it, blew it out and retried and still no movement. are the 2 valves in the...
  12. F

    source of 48volt dc drive motor

    i have a drive motor #74643gt on my genie z34/22dc that 1 section of the field is burnt/black. is there other sources besides genie, they are backordered. any idea what may have caused the 1 part of field to go out? thank you
  13. F

    10amp circuit breaker keeps popping

    genie z34/24dc boom lift, finished putting machine back together and everything works, except when trying it out the 10 amp circuit breaker below tilt sensor pops after going forward or backwards several feet. what all affects this circuit breaker that is right below the tilt sensor? i have...
  14. F

    genie 34/22 light codes

    does the consistent blinking every 1.5 sec. of the controller status indicator light mean things are ok or what? the machine won't drive. thank you
  15. F

    which hydraulic hose goes where

    genie 34/24 boom lift. got it in 3 pieces and still putting it together. the hydraulic lines were taken apart at primary boom and a couple were missing. i connected them where i guessed by their lenght . but only 2 toggle switches work as marked. i have moved the hoses to different locations but...
  16. F

    need o-ring source

    repairing 863 bobcat skidsteer. having problems finding correct o-rings for fittings on hydraulic control valve. need 1/4", 3/8" and 1/2" o-rings roe tip of fitting before the threads, but can only be 1/32" thickness. any place besides a dealer. earlier i paid $2.70 for a small o-ring from them.
  17. F

    bobcat 863g hydrostatic motor - keeper/ring broke

    bobcat 863g , took hydrostatic motor apart. found small spring broken on poppet valve and a keeper/ring on piston broken. i was able to order spring from bobcat . but i would have to order the whole block to get ring, several $1000. anyone have 1 to spare or what else i can use in place of ring?
  18. F

    genie wire harness cut

    genie 34/22dc was disassembled in 3 parts. wire harness's were cut. anyone ever spiced these or a source of aftermarket wire harness? thanks
  19. F

    what seal kit for valve body

    hi, i am new to forum and skid steers. have a bobcat 863g that i am rebuilding? what seal kit do i need for the valve body? parts manual lists several. machine is beat up, no serial #. thanks, foolish 3
Top