• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. N

    289 C2 Cat Injection pump question

    I jumped the solenoid with 12 V. It makes no click or noise. How do I remove the cone shape object to the left of the solenoid that you can see in the photograph I Unscrew the solenoid with that there any suggestions thanks It rotates freely so it does not unscrew. I believe it is covering an...
  2. N

    289 C2 Cat Injection pump question

    I turned the key on to purge the air from the new filter and the line turn the key off installed the pressure gauge turn. The key on the pump ran for a few seconds built 7 to 8 pounds then stopped running on its own and the pressure dropped to zero Am I correct in thinking that the transfer pump...
  3. N

    289 C2 Cat Injection pump question

    Good morning We put a pressure gauge on the fuel line and it will build about 7 pounds but it does not hold anything as soon as the electric pump shuts off it drops to zero Is it supposed to hold pressure to the injection pump? Thanks n8t
  4. N

    289 C2 Cat Injection pump question

    Hi thepumpguysc This is a picture of the side of the pump on my 289 C2 Cat skid loader. I am curious what this lever does. If it is a manual shut off, how can I use it to bypass the electric solenoid so I can see if this thing will run Also, does the electric shut off solenoid just unscrew...
  5. N

    289 C2 Cat Injection pump question

    My 289 stalled this afternoon and will not restart. Took The fuel line off at the injection pump and have fuel. I’m going to get a pressure gauge and test it and change the filter in the morning. How many psi should I have at the injection pump? what does the lever on the side of the...
  6. N

    2004 Case CX130

    I had similar problem with the Linkbelt 210lx. There is a small elbow at the bottom of the tank on mine that partially plugs, and I have to remove the fuel line and take a piece of wire and get the crap out of it every once in a while
  7. N

    Deere 850c calibration codes rd

    Does anyone know where I could buy? JT 07237–4. Four pin, PCP test harness. JT 07237–1 Single pin, test, harness Or have instructions on how to build one the John Deere manual I have I do not understand the drawing
  8. N

    Deere 850c calibration codes rd

    Seems to me that the r takes longer than the L to go out I also posted a picture of the PCP wiring
  9. N

    Deere 850c calibration codes rd

    I’ve check the voltage at the fuse panel and I get 27.85 is that range of voltage too high ? at the fuse that goes to the TCU. Also, I checked the ohms on the PCPs on the left motor right motor and front pump and I’ve gotten ranges that are acceptable to what’s in the service manual
  10. N

    Deere 850c calibration codes rd

    Serial number T0850CX898000 I can get all the way through the calibration to where I’m supposed to get how frfr when I hit the calibration button to move to the steps of selling the track speed is when I get the little d and little r The codes I got were F617 miss Track PCP coil shorted...
  11. N

    Deere 850c calibration codes rd

    I can’t get rid of r and d codes d is right track motor speed sensor I replaced it and have is set to @ 22 degrees r is front pump and right motor pcp Any suggestions how to test pcp Should I ohm wire out between speed sensor and tcu Trouble start by not steering left backing up 850c lgp...
Top