• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by foolish

  1. F

    Genie z32/24 boom lift rotator seal

    Yes, I think I have timing right and gears all slide together. I warmed seal in hot water so I could slide it on, would that expand seal?
  2. F

    Genie z32/24 boom lift rotator seal

    I tried a 5# sledge hammer on it and it just bounce back. Is there any chance seal goes in other direction. A picture shows how I took it out, so it should go in same way? The clamp in previous picture won’t squeeze it down anymore. I am doing something wrong!
  3. F

    Genie z32/24 boom lift rotator seal

    Picture of 2 piece high pressure seal
  4. F

    Genie z32/24 boom lift rotator seal

    Thank you I don’t know name for seal but it has a inner part and I was afraid it would pop out if I was too rough with it. I’ll give it a try.
  5. F

    Genie z32/24 boom lift rotator seal

    I am trying to put new seals in the basket rotator. I can not get the pressure seal in. I warmed it in hot water to slip it on and then used a hose clap from turbo hose to squeeze it down. It is still to big to get in housing. The side that goes in 1st is flared which makes it harder.
  6. F

    10amp circuit breaker keeps popping

    sorry TxHayseed, seems like i can't find it. went through service manual twice yesterday and didn't see level sensor replacement. could you please post it for me. thanks
  7. F

    10amp circuit breaker keeps popping

    thanks guys. just got my digital level so will try that. txhayseed do you have the values for using volt meter? i would like to try that ,too.
  8. F

    10amp circuit breaker keeps popping

    thank you, i also had damaged wires under machine and repaired them and put the split plastic wire loom over them. circuit breaker is not popping now. still trying to get tilt sensor level. just ordered small digital level to use on top of sensor to try and set it.
  9. F

    genie boomlift decreased groundspeed

    it is working. thanks for all the help. i had 1 wire wrong on the limit switch by the turn table. and i checked connections of tilt sensor to ground control panel. thanks , bruce
  10. F

    genie boomlift decreased groundspeed

    when the joy stick is pushed forward or backwards it will move faster the more it is pushed. i don't know how to test it as there are 3 parts that rotate and a number of wires.
  11. F

    genie boomlift decreased groundspeed

    still have problem with ground speed. i put on 2 new limit switches. did the flow chart for machine will not drive at full speed and it all check out ok, and no fault codes. but there are 4 limit switches and it does not show how to check out ?#3 limit switch which i think is the 1 down under...
  12. F

    bobcat 863 blowing seals in carrier

    thanks for all the help. once i got the hyd. lines connected correctly it works great. bruce
  13. F

    bobcat 863 blowing seals in carrier

    thank you, i'll try and put it together this weekend. looks like i have 1 to go to tank drain and 1 to go to hyd pump.
  14. F

    bobcat 863 blowing seals in carrier

    i think i screwed up royally. i had to disconnect all the hoses and tubes when i replaced axle bearings and races. i did not mark all the hoses. i took lots of pics but not enough. does anyone have a diagram of which hoses go to which end of drain filter?
  15. F

    bobcat 863 blowing seals in carrier

    i did put a new drain filter in when overhauling this machine. it doesn't even have a hr of time on it, but i will reck it. my hydrostatic motor and carrier is very different from final drive in video. the fluid from hydrostatic motor flow blows the seals in carrier , then into chain case and...
Top